Commercial Water Filtration

Reverse Osmosis

Commercial water softener systems

Compact Series III

  • Compact design requires minimal installation space
  • Designed for municipal/tap water source
  • Quality components utilized for system construction
  • Designed for optimum water recovery
  • Adjustable waste and recycle flow controls
  • Quick and easy system installation
  • Available for pressure or open tank applications
  • Output Production: 150 gpd up to 800 gpd

Feed Water Parameters:

Temp. 85 F maximum / Pressure 40 – 80 psi maximum / TDS 2000 ppm maximum. If higher consult factory / Iron tolerance 0.5 ppm maximum / Hydrogen sulfide must be removed / Silica tolerance can not be higher than 125 ppm in the concentrate stream. Antiscalant should be considered for any levels over 75 ppm. / Turbidity should be removed / Hardness over 10gpg should be softened.

Operating Parameters:

Operating pressure 200 psi maximum / Water recovery is factory set at 33 – 35% / pH range 3-11/ Flow Rates are determined by the membrane mfgr’s. testing criteria of 1500 ppm Nacl solution, 77 F water temperature, 225 psi at 10-15% recovery. Actual flow rates may vary depending on the pre-treatment used, water conditions, system size, membrane array and applied pressure.

Options

  • Product and waste flow meters
  • Automatic hourly flush
  • Manual flush
  • Stainless steel needle valves
  • 220 volt motor
  • Float switch for atmospheric storage tank
  • Stainless steel pump
  • Stainless steel membrane housing
  • Additional pre-treatment, see below:

The pre-filtration on the COMPACT is sufficient for the 150 an 250 gpd models. It is advisable that additional pre-treatment be installed in front of the COMPACT for the 450 and 800 gpd models. Higher volumes of water passing through the COMPACT can shorten filter life.

Model Specs:

Model GPD(minimum) Membrane
Piping
inlet waste prod
Dimensions
COM-III 150 150-200 2.5” X 14” 1 ea. 3/8" 3/8" 3/8" 14” X 16” X 30”H 85lbs
COM-III 250 300-400 2.5” X 21” 1 ea. 3/8" 3/8" 3/8" 14” X 16” X 30”H 88lbs
COM-III 450 500-600 4” X 14” 1 ea. 3/8" 3/8" 3/8" 14” X 16” X 30”H 92lbs
COM-III 800 800-900 4” X 21” 1 ea. 1/2" 3/8" 3/8" 14” X 16” X 30”H 95lbs


 

Details:

  • Thin Film Composite Membrane
  • PVC membrane housing
  • Powder-coated steel frame
  • Inlet and outlet pre-filter gauges
  • Liquid-filled system pressure gauge
  • Pressurized tank pressure gauge
  • Adjstbl. Waste/recycle needle valves
  • High-pressure nylon tubing
  • High-pressure brass comp. fittings
  • Storage tank pressure switch
  • Low-pressure switch
  • Feed water inlet solenoid valve
  • 1/2 hp 50/60 hz motor
  • Rotary vane pump
  • 20” 5 micron sediment pre-filter
  • 20” carbon block pre-filter
  • Salt rejection 95-99%

View the Compact III Commercial RO Powerpoint View the Power Point brochure (requires Microsoft Power Point)


 

Water Softeners / Conditioners

LC-200 Light Commercial Single Tank Softeners

LC-200 Light Commercial Single Tank Softeners (2")

  • 2" valves for high flow rates
  • Top quality components
  • Models for capacities to 600,000 grains
  • User friendly Fleck 2900 control valves
  • Brine tanks with grid plate for maximum saturation of brine (some models)
  • Safety brine valve with air check.

View the LC-200 Light Commercial Single Tank Softeners RTF Document View the Rich Text Format brochure document



95 MT-150 Light Commercial Twin Alternating Series Commercial water softener

95 MT-150 Light Commercial Twin Alternating Series (1 1/2")


 

Advanced Water Systems 95 MT-150 Twin Serieswater softeners (8 models) are suitable for commercial applications ranging from 60,000 to 300,000 grains of hardness removal capacity at flow rates up to 47 gpm. Installations might include restaurants, car washes, laundromats, small boilers, and other light commercial applications where a continuous supply of soft water is required. The LCTA 150 is a twin unit alternating system where one unit is in service and the other unit is in stand-by.

Operation of The Softener: Hard water contains dissolved minerals in the form of Calcium (Ca), Magnesium (Mg), and Iron (Fe). Removal of these minerals is accomplished by softening the water through an ion exchange process. As water flows through the mineral tank, the dissolved minerals become attached to the resin. Over a period of time the resin will become ex­hausted, and the softener will regenerate using a brine solution.

Softening Media: The exchange media is a high quality black strong acid softener (Cation) resin in the sodium form with a very high whole bead count, no color throw, physically hard, and is chlorine resistant. The media combines high operating capacity with excellent chemical and physical stability for long dependable life. Request media specifications for details.

Controller/Meter: Regeneration cycle can be initiated by day time-clock or optional meter initiated regeneration cycle after a pre­set volume of water has been softened.

Regeneration Controller: The 95 MT-150 Twin Series softeners are controlled by a reliable Fleck electro­mechanical controller. The fully adjust­able 5 cycle, single controller operates all steps and regeneration cycles for both vessels, including upflow back­wash, downflow brining and slow rinse, rapid rinse, brine refill and downflow service.

Control Valve: The sequence control valve operates on commands from the valve controller. A hydraulically balanced piston glides effortlessly along non-corrosive spacers and seals to a precise position. This precision motor-driven valve performs in the toughest applications and is made of high quality brass for a long and reliable life. A single valve regenerates and controls flow through both resin tanks.

Resin Tank: All 95 MT-150 Twin Series models feature non corrosive fiberglass tanks, with a one piece thermoplastic inner liner. The tanks have a maximum working pres­sure of 150 psi and a working tempera­ture of up to 120°F. The tanks are approved by NSF, UL, and meets WQA Standard S-100, and FDA. All fiberglass tanks carry a 5 year warranty.

Brine Tank: The brine tank is a combination brine maker and salt storage vessel, and is made of tough, high density polyethylene and features a grid plate for maximum saturation of brine. Larger tanks are available for extra salt storage capacity.

Brine System: Brine refill is automatically controlled by the timer/ controller to provide the correct amount of brine for each regeneration. The refill system is backed up by a float and safety valve shut-off, which minimizes the chance of overflowing the brine tank.

Water Meter: The water meter is standard on all models. Regeneration is initiated when a preset volume of water is used. Once the meter gallon setting zeros out, the system automatically switches tanks and the exhausted tank goes immediately into regeneration. Once regeneration is completed the tank goes into the standby mode.

View the 5 MT-150 Light Commercial Twin Alternating Series RTF Document View the Rich Text Format brochure document

Advanced Water Systems Limited Warranty: Advanced Water Systems softeners are guar­anteed to be free of manufactur­ing defects at the time of installa­tion. Warranty period begins on installation date, but shall not ex­ceed six months from manufactur­ing date. There is a one year war­ranty on steel tanks, and component materials, a two and a half year warranty on control valves, and a five year warranty on brine tanks, and one year on optional steel tanks.